Muddy Footage GY HM600
 

Hey, anyone else with the GY HM600 feeling like their footage looks muddy? Even with what feels and looks on camera to be a good focus my shots feel very muddy after the fact. I am editing in FCPx but even just viewing the files they look blurry. I am shooting at 180° on 24p at 1080. I may try cranking up the detail in camera again and see if that helps but it is bugging me a little bit. The shot of the royal crest on the castle was pin sharp in the Viewfinder (eyepiece not LCD screen).

Re: Muddy Footage GY HM600
 

Do you know what your average f-stop was? Softness in daylight bright footage could be the result of diffraction when no nd is applied and the camera needs to close down the iris completely to compensate, which it can't.

Re: Muddy Footage GY HM600
 

Agreed, the colors are muted, the sharpness isn't what you would expect, and the images seem somewhat dark and muddy.

Might be you want to tweak the camera setup, see instructions starting at page 92 in the manual. You can increase contrast, set the black point, arrange color balance, sharpening, etc. to your taste.

Might also check your FCPx settings, you might have inadvertently set a default for, say, broadcast limits (which constrains the density range of the image to suit broadcast requirements) or some such.


Best wishes!

Re: Muddy Footage GY HM600
 

Not sure if this helps but there are some recommended settings in this document:

http://tech.ebu.ch/docs/tech/tech3335_s07.pdf

I don't have the experience to be changing the contrast/colour/knee, etc, settings myself so I used those recommended settings and haven't had any issues.

Re: Muddy Footage GY HM600
 

I am using those settings Jody, I can not remember my exact IRIS, but I have been trying to keep it under 5.6

I know i had the Gain on 0 and the ND at 1/64, however that sometimes does not appear to be enough, do you suggest using negative gain or should I increase framerate ?

Re: Muddy Footage GY HM600
 

I had detail on -7 I suspect that would be the problem. I have put it at around +3 now, I believe it was -7 due to the article, I am going to reread that and make sure I didn't do it incorrectly.

Also, not able to do a negative gain (makes sense) so I will possibly need to start using my Polarizer outside.


I highly suspect that the -7 detail is what caused this issue, as I do not remember the camera being that muddy previously. The sun is already setting, so I am going to head out right now and see if I can snag a few handheld shots from the Citadel.

Re: Muddy Footage GY HM600
 

I use -6 gain unless I'm in low light. I find that even 0dB is slightly grainy when lighting isn't ideal but -6 is extremely clean. To achieve -6dB gain you need to set "extended mode" in the settings.

I also have my detail set to -7 though, so I'm wondering if that's what is causing the grain. Let me know how +3 detail is for you.

Re: Muddy Footage GY HM600
 

Thank you very much for the -6 gain trick, that helped a lot. Also I pumped it up to +3 detail and I find that it aliases a little bit, but is more crisp over all which I prefer. I took some footage but since I'm at the S.O.'s family for easter I haven't really bothered to put anything up!

Re: Muddy Footage GY HM600
 

This was all shot with -6dB, and the stuff where we still had decent light looked ok, but I definitely got quite a bit more noise as the light dipped away. This was apparent BEFORE I graded but definitely obvious after. However I think it all still looks ok.

I shot with detail at +3.

Any suggestions on what I can do with my settings etc? I was running for most of it so I could stay in the right IRIS.

I feel like i'm still not quite getting everything out of the camera, also realizing just how much I have forgotten.

Re: Muddy Footage GY HM600
 

I've noticed my HM600 produces a very grainy image in low light even at -6dB gain also. So I'd also be interested in any information about any different settings that may help with this.

Re: Muddy Footage GY HM600
 

and so I continue playing with the camera, I would say this is a HUGE step forward in quality from what I had originally. I am using the Alex4D unsharp mask and that has made a difference as well (thought not necessary I do like how it looks).

The big trick was lowering the green matrix a bit, and colour grading the footage afterwards.

Re: Muddy Footage GY HM600
 

Negative gain reduces the dynamic range of you camera so it should be used judiciously. Check Alister’s site for a fuller explanation. The less the dynamic range the flatter looking your image will be.

Why using negative gain can be bad, unless you have an F3. | XDCAM-USER.COM

Chris Young
CYV Productions
Sydney

Re: Muddy Footage GY HM600
 

If I understand correctly that affects the low end of the image blacks and such, or would that limit in the dynamic range affect the high end? So far in my footage I have not actually found any noticeable limit in how much dynamic range I have.

Re: Muddy Footage GY HM600
 

Hi ~

If you switch in -6dB you are reducing the dynamic range by one stop. You are effectively moving the entire output from the sensor down by a stop. You are correct negative gain makes for less sensitivity in the dark areas of the image and in turn the image will appear to have less noise in the low light areas because you have effectively crushed visibility in the blacks. Conversely though your maximum levels are now down as well. In effect the range you have to reproduce the image is down by one stop. Example, in a camera with a ten stop range you have lost ten percent of its dynamic range. Sadly the less dynamic range your camera has to operate in makes for a flatter less vibrant looking image.

Chris Young
CYV Productions
Sydney

Re: Muddy Footage GY HM600
 

fantastic, thank you :)

Is that something you personaly noticed in my footage or just a warning based on reading the article? From my experience grading this footage, running in the wdr mode with the -6dB i've not seen any loss of range.

I know in my earlier footage with 0dB or +6dB I had very little detail in the low end and low midrange tones, it was noisy and just had zero detail to pull out when grading. I do not know if it is because I switched to WDR or if it is the positive gain but it definitely gives me a cleaner range of image now. Thank you for giving me something to play with