De-interlacing method
 

I am using pair of consumer camcorders - AVCHD for my 3D @ 60i. When I play the resulting video on TV, it seems o.k. due t the decent de-interlacing technique - I am guessing. When I play back on computer or over internet (YT/Vimeo) I have annoying artifacts due to interlacing. I tried to use several de-interlacers, but I canot find one that works well. Does anyone have any suggestions for good de-interlacer?

Re: De-interlacing method
 

It depends on what platform you're on. Revision FX's Fieldskit is pretty good & also works on many platforms. If you're on Mac, use compressor & set the deinterlacing to "blend". On a budget, try JES Deinterlacer.

Re: De-interlacing method
 

Thanks Arnie. I work on either Windows or MacOS and would like to use decent de-interlacer on either. Your advice is very helpful and I appreciate it.

Re: De-interlacing method
 

Hi
Try ffdshow with deinterlace checked (yadif method)
This gives me smooth result!

Re: De-interlacing method
 

Thank you Prech. I'll give it a try.

Pavel

Re: De-interlacing method
 

I'll second yadif. It beats the adaptive, motion-compensated de-interlacer in Compressor hands down (and every other software de-interlacer I ever tried).

Re: De-interlacing method
 

When is the best moment for de-interlaced? Do you de-interlace L and R clip separeted or do you de-interlaced once the are ensambled?
Thank´s

Re: De-interlacing method
 

De-interlace as a first step, fresh out of the camera. Any transcoding or frame manipulation might have the unintended consequence of blending the two fields from the camera - which need to be pristinely separated for proper de-interlacing.

Re: De-interlacing method
 

How can i play Sony TD10 native files with Stereoscopic Player
with good deinterlace (bob, yadif, etc)?

Re: De-interlacing method
 

I'll look into the ffdshow, especially since I'm doing all my stereo work on PC.

Does anyone have a sample interlace vs. de-interlaced stereo comparison samples link, so I can see them side-by-side?

Re: De-interlacing method
 

Stereoscopic Player will deinterlace on the fly. Depending on your video card, you'll generally get quite decent hardware deinterlacing.

Re: De-interlacing method
 

FYI - AVISynth can run YADIF as well.

Re: De-interlacing method
 

I have only a geforce 210 card. Can i use this with Stereoplayer for high quality deinterlacing?

Re: De-interlacing method
 

I've never seen really bad deinterlacing from an NVIDIA card, but, reviews say otherwise for the 210 card:

AnandTech - Quick Look: MSI?s GeForce 210

"The quality is reminiscent of vector adaptive deinterlacing, however it’s not as clean as what we’ve seen on the GT 220."

It's still worth a try.

Re: De-interlacing method
 

When i check deinterlace to on in Stereoscopic player, it will use the gpu hardware deinterlacing? Sure?
After turned on, the horizontal lines disappear, but i don't get smooth motion. I see 25fps progressive (from 50i source), and not 50fps.
I can see my 50i mpeg2 videos at 50fps deinterlaced with bob or yadif method via ffdshow. But when i
load native videos from TD10, i cannot change deinterlace method at "video properties" under used filters.
Only 3dtv.at AVC/MVC decoder is used, and i cannot setup here anything.

So i really need a new video card? A GT240 support good deinterlacing?
thx