Are there any instruction manuals available out there for the MA200?

It's been many years since I bought mine but I don't remember them coming with any kind of manual.
What is it you have a question on?
Randy

It's been many years since I bought mine but I don't remember them coming with any kind of manual.
What is it you have a question on?
RandyI have a small audio/video crew that shoots the local football team each week.We do a post edit and then replay the game on the local cable community channel.

We set up the camera on top of the press box with two announcers. Currently I used a Behringer audio mixer, the announcer's broadcast headsets are fed into that device. I use 2 RCA audio cables from the Behringer to feed the audio into the Audio 1 Input on the back handle of the XL1.

Here is finally the question. What type of Broadcast Headset with built in mic are recommended to connect directly into the MA200? I plan to use a Y-Splitter for the headphone input on the top rear handle of the XL1 for the announcers to monitor the audio feed.

I currently use Yamaha CM500 Headset with the Behringer audio mixer. The Yamaha CM500 mic cable has an inline power supply (2 AA batteries) feeding the audio input into the mixer. I was hoping to use the same headsets with a 3.5mm to XLR adapter to plug into the MA200.

I ordered the MA200 and waiting for it to arrive. Just wanted to do my homework prior to it's use.

Hopefully I explained myself thoroughly. I do computer software consulting to make my living and have a passionate hobby with the audio/video crew of volunteers.

Any suggestions are greatly appreciated.

www.coogsports.net (http://www.coogsports.net)

I have no suggestion for the headset but I will say the headphone jack on the XL1 (and XL1S) is notorious for not putting out enough volume for one set of headphones much less two.
If the Behringer has direct outs I would have one announcer come out of one channel and the other come out of another from the direct outs for that specific channel. Since there's only two you could also come out the left and right from the main outs.
Hope that helps,
Randy

I have no suggestion for the headset but I will say the headphone jack on the XL1 (and XL1S) is notorious for not putting out enough volume for one set of headphones much less two.
If the Behringer has direct outs I would have one announcer come out of one channel and the other come out of another from the direct outs for that specific channel. Since there's only two you could also come out the left and right from the main outs.
Hope that helps,
RandyI guess I didn't explain myself (like I knew I would). I am going entirely with battery power. The XL1, the Varizoom monitor will use batteries. With the purchase of the MA200, I will not need the Behringer audio mixer(or so I thought) which works on 120v.

That was the purpose of buying the MA200.To plug a powered mic directly into it. Did I make a mistake?

If the announcers don't need to monitor anything through the headset you should be good to go.
As I understand it your just talking about plugging mics into the MA200 right?
By the way, not remembering if the MA200 comes with any literature on them, if you ever decide to go 3 or 4 track audio you'll need to select it in the XL1 menu and go 12 bit instead of 16.
You would also need software capable of capturing more than 2 channels (ie Scenalyzer)
Good luck,
Randy

If the announcers don't need to monitor anything through the headset you should be good to go.
As I understand it your just talking about plugging mics into the MA200 right?
By the way, not remembering if the MA200 comes with any literature on them, if you ever decide to go 3 or 4 track audio you'll need to select it in the XL1 menu and go 12 bit instead of 16.
You would also need software capable of capturing more than 2 channels (ie Scenalyzer)
Good luck,
RandyThanks.....I was hoping that I did not need any additional devices between the headset w/mic and the MA200.

Actually, I am also using a Firestore Fs-4. I export the audio/video signal directly into it via the firewire connection on the right side of the XL1. I will have to experiment with the 16 bit and 12 bit options. I'm not sure if it will capture all audio inputs with the XL1 in the 12 bit ST1,ST2 mix mode.

I will say the headphone jack on the XL1 (and XL1S) is notorious for not putting out enough volume for one set of headphones much less two.

Notorious maybe a bit of strong statement. The output is adequate for typical headphones such as the Sony MDR-7506 or MDR-600, with sensitivities on the order of 105 dB/mW and impedance around 50 ohms, but it does not have sufficient power for the low efficiency/low impedance headphone some folks have tried.

Notorious maybe a bit of strong statement. The output is adequate for typical headphones such as the Sony MDR-7506 or MDR-600, with sensitivities on the order of 105 dB/mW and impedance around 50 ohms, but it does not have sufficient power for the low efficiency/low impedance headphone some folks have tried.Thanks Don....one last question or request for advice. What does the group recommend as a wireless mic and receiver combo to be used with the MA100 or MA200?

The Audio forums probably would have more info on help in selection of a wireless mic.

First, In most cases you can connect a wireless mic direct to the camcorder input jacks (the RCA) and skip the XLR adapter, if you like. HOwever, if you want to go throughthe MA-100/200 Note that the MA100/200 are designed for mic-level signals, and will clip if fed a line level signal. And you may ned to find proper cable or adapter to go from the wireless mic output to the XLR input.

I've used several wireless including models form Azden WDR-Pro (low cost VHF), Samson, Shure (older VHF) and more recently from the Sony UWP series UHF. with satisfactory results for my applications (mostly event video). Many folks who appear in these dvinfo forums like the Sennheiser Evolution G 100 series systems.

"HOwever, if you want to go throughthe MA-100/200 Note that the MA100/200 are designed for mic-level signals, and will clip if fed a line level signal."
Actually Don, with a menu selection in the XL1S you simply select line instead of mic...I run a mixer into mine at times (just remember to switch it back : ))

It is the actual circuits in the MA100/200 that will start to clip if the input signal exceeds around -7 dBV, not the camcorder. While that is above nominal consumer line level (which is -10 dBV) it can be trouble for professional line levels which are more like +4 dB.

This is a hard limitation based in part on the power supply voltage.