Rode NTG-2 too slim for A1 shotgun holder? at DVinfo.net

Carrie Cannaday · February 19th, 2008, 02:02 PM

Hello all,

I just purchased a Rode NTG-2 shotgun mic for my Canon XH-A1. So far the only issue that I've had is the shotgun holder on the A1 seems to be too big for the NTG-2. The NTG-2 slips and slides inside the shotgun holder. I have a shock-mount that will mount onto the cameras shoe mount, but I'd prefer to use the camera's shot gun holder and free up my shoe mount for other uses. Anyone have any advice?

Bill Pryor · February 19th, 2008, 02:11 PM

You can wrap a little black gaffertape around the mic, or a rubber band...or go to a hardware store (take the mic) and get a couple of rubber O-rings that will go around the mic. Or glue some pieces of rubber or foam to the inside of the mount. The O-ring solution is probably the least inelegant.

Robert Morane · February 19th, 2008, 02:19 PM

The O-ring also give a little suspension and better isolation to the mike, works very well.

Carrie Cannaday · February 19th, 2008, 02:30 PM

Thanks for the advice on the o-rings, I'll have to check into that. For some reason now that I think back I'm wondering if the A1 didn't include a package of o-rings in the box? Or, is that a figment of my imagination?

Benjamin Hill · February 19th, 2008, 03:02 PM

Quote:

Originally Posted by Carrie Cannaday

Hello all,

I just purchased a Rode NTG-2 shotgun mic for my Canon XH-A1. So far the only issue that I've had is the shotgun holder on the A1 seems to be too big for the NTG-2. The NTG-2 slips and slides inside the shotgun holder. I have a shock-mount that will mount onto the cameras shoe mount, but I'd prefer to use the camera's shot gun holder and free up my shoe mount for other uses. Anyone have any advice?

I ordered a shockmount with my NTG-1 and use that. The Canon mic holder is not only too big, the inside is very stiff and offers little vibration dampening for sensitive mics. Not sure what they were thinking with that design.

Hubert Duijzer · February 19th, 2008, 03:18 PM

Rode SM-5 is a cheap and good shockmount

Kellen Dengler · February 19th, 2008, 03:24 PM

Hubert, where did you find the Softee cover for the XH A1 built in mic?

Jim Miller · February 19th, 2008, 03:28 PM

I second the use of the sm5. It also gets the mic further away from the lens when you mount a deadcat or other wind noise reducing device.

Todd Smaretsky · February 19th, 2008, 03:29 PM

I have not yet found a mic that actually fits the a1. Simply use tape; but, be careful in the tape you use. Don't damage your mic body.

Hubert Duijzer · February 19th, 2008, 03:43 PM

@Kellen
Not so long ago: http://www.dvinfo.net/conf/showthread.php?t=111955 The ebay link.
It fits really thight and it looks good to me.

Robin Hall · February 19th, 2008, 03:51 PM

I Had the same issue with my AT-897, as mentioned already O-rings were my solution, seems to work just fine.

Trish Kerr · February 19th, 2008, 06:06 PM

I use gauze on mine with an elastic band - it happened to be handy the first day I had to put it on the camera and I've just kept it. Soft against the mic but holds it quite well. And no it's not pretty, but it does give the camera a bit of a 'veteran' feel.

Trish

Don Palomaki · February 19th, 2008, 06:14 PM

I use about two turns of black gaffer tape. And to minimize coupling of vibration to the mic, tighten the camcorder mic mount screw just enough to keep the mic from sliding in the mount.

Tripp Woelfel · February 19th, 2008, 08:20 PM

You all might be overtaking the plumbing on this. I followed someone's advice and looped the extra mike cable thru the mic holder. That way, it fits just fine. It doesn't provide any more shock mounting so your other solutions might be better, particularly the fancy shoe mounts. I've had no problems with the Rode in the camera mount with that loop of mic cable in there.

The price was right and it keeps the extra cable out of the way.

Arnold Tersteeg · February 20th, 2008, 01:43 AM

Quote:

Originally Posted by Kellen Dengler

Hubert, where did you find the Softee cover for the XH A1 built in mic?

Kellen i make one self, works perfect and cost not more than 50 cent !

February 19th, 2008, 02:02 PM	#1
Carrie Cannaday New Boot Join Date: May 2007 Location: United States Posts: 20	Rode NTG-2 too slim for A1 shotgun holder? Hello all, I just purchased a Rode NTG-2 shotgun mic for my Canon XH-A1. So far the only issue that I've had is the shotgun holder on the A1 seems to be too big for the NTG-2. The NTG-2 slips and slides inside the shotgun holder. I have a shock-mount that will mount onto the cameras shoe mount, but I'd prefer to use the camera's shot gun holder and free up my shoe mount for other uses. Anyone have any advice?

February 19th, 2008, 02:30 PM	#4
Carrie Cannaday New Boot Join Date: May 2007 Location: United States Posts: 20	O-rings Thanks for the advice on the o-rings, I'll have to check into that. For some reason now that I think back I'm wondering if the A1 didn't include a package of o-rings in the box? Or, is that a figment of my imagination?

February 19th, 2008, 03:18 PM	#6
Hubert Duijzer Regular Crew Join Date: Oct 2006 Location: Netherlands Posts: 177	Rode SM-5 is a cheap and good shockmount Attached Thumbnails

February 19th, 2008, 06:14 PM	#13
Don Palomaki Wrangler Join Date: Sep 2001 Location: Northern VA Posts: 4,487	I use about two turns of black gaffer tape. And to minimize coupling of vibration to the mic, tighten the camcorder mic mount screw just enough to keep the mic from sliding in the mount. __________________ dpalomaki@dspalomaki.com

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search

February 19th, 2008, 02:11 PM	#2
Bill Pryor Contributor Join Date: Jan 2003 Location: Kansas City, MO Posts: 4,449	You can wrap a little black gaffertape around the mic, or a rubber band...or go to a hardware store (take the mic) and get a couple of rubber O-rings that will go around the mic. Or glue some pieces of rubber or foam to the inside of the mount. The O-ring solution is probably the least inelegant.

February 19th, 2008, 02:19 PM	#3
Robert Morane Major Player Join Date: Apr 2007 Location: Tucson, AZ Posts: 267	The O-ring also give a little suspension and better isolation to the mike, works very well.

February 19th, 2008, 03:24 PM	#7
Kellen Dengler Regular Crew Join Date: Nov 2007 Location: New York, NY Posts: 118	Hubert, where did you find the Softee cover for the XH A1 built in mic?

February 19th, 2008, 03:28 PM	#8
Jim Miller Major Player Join Date: Jan 2007 Location: Tampa,Florida Posts: 236	I second the use of the sm5. It also gets the mic further away from the lens when you mount a deadcat or other wind noise reducing device.

February 19th, 2008, 03:29 PM	#9
Todd Smaretsky Regular Crew Join Date: Sep 2007 Location: Los Angeles, CA Posts: 36	I have not yet found a mic that actually fits the a1. Simply use tape; but, be careful in the tape you use. Don't damage your mic body.

February 19th, 2008, 03:43 PM	#10
Hubert Duijzer Regular Crew Join Date: Oct 2006 Location: Netherlands Posts: 177	@Kellen Not so long ago: http://www.dvinfo.net/conf/showthread.php?t=111955 The ebay link. It fits really thight and it looks good to me.

February 19th, 2008, 03:51 PM	#11
Robin Hall Regular Crew Join Date: Jan 2008 Location: London On Posts: 43	I Had the same issue with my AT-897, as mentioned already O-rings were my solution, seems to work just fine.

February 19th, 2008, 06:06 PM	#12
Trish Kerr Major Player Join Date: Mar 2007 Location: Canada Posts: 294	I use gauze on mine with an elastic band - it happened to be handy the first day I had to put it on the camera and I've just kept it. Soft against the mic but holds it quite well. And no it's not pretty, but it does give the camera a bit of a 'veteran' feel. Trish

February 19th, 2008, 08:20 PM	#14
Tripp Woelfel Trustee Join Date: Jan 2008 Location: North Conway, NH Posts: 1,745	You all might be overtaking the plumbing on this. I followed someone's advice and looped the extra mike cable thru the mic holder. That way, it fits just fine. It doesn't provide any more shock mounting so your other solutions might be better, particularly the fancy shoe mounts. I've had no problems with the Rode in the camera mount with that loop of mic cable in there. The price was right and it keeps the extra cable out of the way.